![](/static/253f0d9b/assets/icons/icon-96x96.png)
![](https://lemmy.world/pictrs/image/8286e071-7449-4413-a084-1eb5242e2cf4.png)
A reverse proxy needs you to forward ports 80 and 443, unfortunately.
A reverse proxy needs you to forward ports 80 and 443, unfortunately.
YNAB was a life changer for me, so it’s hard to talk badly about it, but I did move on to something more reasonable once I got my shit together.
IMO people should get started with YNAB, use the YNAB “rules”, and once they know how it all works, switch to something like Budget with Buckets.
Buckets is not as refined, but the price is right. I do bank syncing with the SimpleFIN Bridge option which is $1.50/month, and I have fewer problems with it than I did with YNAB.
I have a bunch of z-wave, too. Z-wave and Zigbee, I think, only broadcast when needed. That’s why they’re much more battery friendly. If they’re plugged in, they do more listening and re-broadcasting to do what you’re talking about.
Wifi has, relatively, a ton more traffic. DHCP renewals, keep-alive messages, and basically always listening all the time to see if something is looking for it. That being said, these smart switches use very little data overall. Unifi shows them using about 700 bits per second, which is 0.0007 Mbps.
Actually now that I think about it, without more than 1 access point, everything will all be on the same channel. I have 3 different channels due to having 3 different access points, all set to individual channels. This reduces conflicts (more than one device trying to use the same channel at the same time, a weakness of wifi).
As of right now, my “busiest” access point has 23 devices connected to it on 2.4 GHz. The AP is reporting that channel being 23% utilized. Still, I wouldn’t want anywhere near 100% utilization. Things would certainly slow down as it gets higher.
Newer versions of WiFi reduce this problem, but smart devices use whatever is cheap and effective. 2.4 GHz travels better through walls and has better range compared to 5 GHz, but 5 GHz is faster and has more available channels.
I currently have 54 things connected to WiFi in my house. Only 10 of those are connected to 5 Ghz. The rest only support 2.4.
With one good access point it would probably work no problem. I have 3 access points due to the layout of my house.
Use channels 1, 6, and/or 11. Those are the only channels that don’t overlap with other channels. If you live in a dense area, 2.4 gets tricky. 5 is easier, because more channels.
They work like regular switches. The flip of the physical switch sends the change back to home assistant to keep everything synchronicity.
I don’t have any, though, so I’m not sure if you can set it to “up is always on”, or if it ends up being a switch, so “whichever direction just changes the on/off state”
Thanks for posting this!
Meh, even then. If they’re 60MB each that’s only 120GB.
Noticeable difference loading the page? Loading photos? Uploading photos?
Photo files are relatively small, so an HDD is absolutely fine.
Oh thanks for the heads up
Big trouble, mister. They’re gonna git you!
I feel ya. Make a fake GitHub account, maybe?
Or manually download each custom component that you want?
I installed MagicMirror onto a Raspberry Pi using a pre-made Magic Mirror OS image (can’t remember where I got that, but I think it’s relatively “official”, so maybe their website? It comes ready to go with Docker and everything you need set up.
Then I installed this https://github.com/pelaxa/MMM-ImmichSlideShow and configured it.
I actually found some additional configuration options by going back in the chain to the project it’s based on (linked at the top of the readme). Their documentation included some additional stuff that actually works with MMM-ImmichSlideShow. Edit: Looking at my config again, and all the stuff is in the MM-ImmichSlideShow documentation now. Maybe they updated it.
Then I hooked up an old monitor, put it in vertical mode, and that’s it.
It was actually kind of difficult to figure out how to get the display to work in vertical mode. A lot of old forum posts are the “old” way of doing it. I ended up making a cronjob that runs 60 seconds after boot and runs some command that rotates the display. I’ll dig it up if you need me to, but since MMM-ImmichSlideShow is still broken it’s not turned on right now so I can’t check it. Here’s the line from my crontab to rotate the display: @reboot sleep 60 && DISPLAY=:0 xrandr --output HDMI-1 --rotate right
Aha, that must be it. The photo in question is 6.7MB
I’m able to save a trail without any photos, but if I try to add a photo it lets me select the photo, but saving the trail gives a toast notification in the bottom right that says “Error saving trail.” The web, db, and search logs don’t show any errors.
Mine was having some weird problem with docker, I think it must be a docker bug. Basically it put the Wanderer stuff at the very bottom of the routes (running “sudo route” on Debian lists the routes). The last entry in the routes table needs to be eth0 or the equivalent so that stuff can loop back to the beginning of the list. At least that’s my understanding.
So anyway, to get around that bug/limitation I had to create a static docker network which I called “wanderer-static” using docker network create --attachable -d bridge --subnet 172.28.0.0/16 --gateway 172.28.0.1 wanderer-static
. Choose a subnet that’s not being used already.
Then in the docker compose file, point everything at that network by:
Removing
networks:
wanderer:
driver: bridge
Adding
networks:
wanderer-static:
external: true
And finally, pointing each service to that network. Under each service you should have:
networks:
- wanderer-static
I also had to update the ORIGIN and whatever else to http://wanderer-static:7000
, etc.
Immich is the only thing I run where I check the change log before doing any sort of update. It’s worth it, though. Great software.
This update broke my janky little raspberry pi “photo frame” which uses MagicMirror and a plugin. I probably just need to rename a port in the plugin or something (or wait for an update).
Looks cool. I have it up and running with the docker compose provided. Every time I try to create a user it says “Error creating user”, and the logs say [ERROR] [23:30:00]: Login failed. Unable to obtain cookie.
Edit: I got it working, just had to updated some of the network stuff in the docker compose. The networking in Portainer is a bit “complex”.
I can’t get photos to work. Oh well.
Oh actually it looks like maybe it’s fixed. The issue was closed 5 hours ago https://github.com/jellyfin/jellyfin-uwp/issues/39
Edit: I’m confused. I’m not sure what the media player has to do with the Xbox app.
Cool, nice.